|
JRRB211N
|
ROBINSON
NYLON BRUSH
|
|
RECOMMENDED
FOR REMOVING SOFT DEPOSITS (MUD, ALGAE, ETC.) IN STRAIGHT,
NON-FERROUS TUBES
(COPPER, BRASS, PLASTIC, ETC.). BRUSH SHOULD BE EQUAL TO
OR 1/16" SMALLER THEN TUBE I.D.
(SIZES SHOWN ARE ACTUAL O.D. OF BRUSH) |
|
|
8-32
MALE THREAD |
| 1/4"
(6.4MM), 5/16" (7.9MM), 3/8" (9.5MM) |
| 1/4
- 28 MALE THREAD |
| 7/16"
(11.1MM), 1/2" (12.7MM), 9/16" (14.3MM),
5/8" (15.9MM),11/16" (17.5MM), 3/4"
(19.1MM), 13/16" (20.6MM) 7/8" (22.2MM),
15/16" (23.8MM), 1" (25.4MM) |
|
|
JRRB200B
|
ROBINSON
BRASS BRUSH
|
|
| RECOMMENDED
FOR REMOVING SOFT AND LIGHT SCALE DEPOSITS IN STRAIGHT,
NON-FERROUS TUBES. BRUSH SHOULD BE EQUAL TO OR 1/16"
SMALLER THEN TUBE I.D. (SIZES SHOWN ARE ACTUAL O.D. OF BRUSH.) |
|
|
8-32
MALE THREAD |
| 1/4"
(6.4MM), 5/16" (7.9MM), 3/8" (9.5MM) |
| 1/4
- 28 MALE THREAD |
| 7/16"
(11.1MM), 1/2" (12.7MM), 9/16" (14.3MM),
5/8" (15.9MM), 11/16" (17.5MM), 3/4"
(19.1MM), 13/16" (20.6MM) 7/8" (22.2MM),
15/16" (23.8MM), 1" (25.4MM) - 1/4-28 |
|
|
JRRB210SS
|
ROBINSON
STAINLESS STEEL BRUSH
|
|
| RECOMMENDED
FOR REMOVING SOFT AND LIGHT SCALE DEPOSITS IN FERROUS TUBES
(CARBON STEEL, STAINLESS STEEL, ETC.). BRUSH SHOULD BE EQUAL
TO OR 1/16" SMALLER THEN TUBE I.D. ( SIZES SHOWN ARE
ACTUAL O.D. OF BRUSH) |
|
|
8-32
MALE THREAD |
| 1/4"
(6.4MM), 5/16" (7.9MM), 3/8" (9.5MM) |
| 1/4
- 28 MALE THREAD |
| 7/16"
(11.1MM), 1/2" (12.7MM), 9/16" (14.3MM),
5/8" (15.9MM), 11/16" (17.5MM),3/4"
(19.1MM), 13/16" (20.6MM) 7/8" (22.2MM),
15/16" (23.8MM), 1" (25.4MM) 1/4-28 |
|
|
JRRBSG
|
ROBINSON
SPIN GRIT BRUSH
|
|
| RECOMMENDED
FOR REMOVING SOFT AND LIGHT SCALE DEPOSITS IN STRAIGHT,
FERROUS AND NON-FERROUS TUBES. THE ABRASIVE IMPREGNATED
NYLON BRISTLES OF THIS BRUSH CLEAN AND POLISH TUBES IN ONE
STEP. UNLIKE REGULAR SPIRAL BRUSHES THE SPIN-GRIT BRUSH
IS DESIGNED TO BE OVERSIZED IN THE TUBE SO THE BRISTLES
LAY OVER, PUTTING THE ABRASIVE IN CONTACT WITH THE TUBE
WALL. |
|
|
JRRBSG50 |
FOR
TUBES 1/4" - 3/8" (6.4 - 9.5MM) |
| JRRBSG750 |
FOR
TUBES 7/16" - 5/8" (11.1 - 15.9MM) |
| JRRBSG100 |
FOR TUBES 11/16" - 3/4" (17.5 - 19.1MM) |
| JRRBSG125 |
FOR
TUBES 13/16" - 1" (20.6 - 25.4MM) |
|
|
JRRBTSG
|
ROBINSON
TAPERED SPIN GRIT BRUSH
|
|
| RECOMMENDED
FOR REMOVING SOFT AND LIGHT SCALE DEPOSITS IN STRAIGHT ENHANCED
CONDENSER TUBES. THE SMALLER DIAMETER STANDS STIFF AND CLEANS
THE GROOVES. THE LONGER BRISTLES LAY FLAT TO CLEAN THE LARGE
AREAS BETWEEN THE GROOVES. THE SMALL DIAMETER OF THE BRUSH
SHOULD MATCH THE TUBE DIAMETER. |
|
|
JRRBTSG500 |
1/2"
- FOR 1/2" (12.7MM) ID TUBES |
| JRRBTSG625 |
FOR
5/8" (15.9MM) ID TUBES |
| JRRBTSG750 |
FOR 3/4" (19.1MM) ID TUBES |
| JRRTSG1000 |
FOR
1" (25.4MM) ID TUBES |
|
<<Back
• Cutting
and Buffing Tools>>
|
